找回密碼
 註冊
樓主: 柒喜

[線材/其它] Hi-End

[複製鏈接]
 樓主| 發表於 2014-3-4 06:50:08 | 顯示全部樓層

                               
登錄/註冊後可看大圖
回覆 讚好 不讚 使用道具

舉報

發表於 2014-3-12 08:21:20 | 顯示全部樓層
本帖最後由 auraheart 於 2014-3-12 08:44 編輯


Sometimes, I wonder if those 3 leg creeps was under the influence of the table table I had in the mid/late 70s-Micro Seiki DDX 1000.  My first so call hi end turn table.

3 legs creep

3 legs creep

DDX 1000

DDX 1000

回覆 讚好 不讚 使用道具

舉報

 樓主| 發表於 2014-3-12 08:50:43 | 顯示全部樓層
auraheart 發表於 2014-3-12 08:21
Sometimes, I wonder if those 3 leg creeps was under the influence of the table table I had in the  ...

好少見人用三支臂
回覆 讚好 不讚 使用道具

舉報

發表於 2014-3-12 09:05:44 | 顯示全部樓層
本帖最後由 auraheart 於 2014-3-12 09:13 編輯
柒喜 發表於 2014-3-12 08:50
好少見人用三支臂


I was one of them.  Had SME 3009 III, (was 3009 II but upgraded when III available) JH formular 4 and infinity black widow.
It was nick named 3 leg creep by Chinese users.  I had one 36 years ago.  Maybe I didn't see enough of hi fi, but never saw 3 legs hi end before that.
Sold that and got Denon with two arms..used Denon for long time..
回覆 讚好 不讚 使用道具

舉報

 樓主| 發表於 2014-3-12 09:19:57 | 顯示全部樓層
auraheart 發表於 2014-3-12 09:05
I was one of them.  Had SME 3009 III, (was 3009 II but upgraded when III available) JH formular 4  ...

黑膠係統迷人地方就係好玩多野玩,乜都可以換,要平要貴任君選擇
回覆 讚好 不讚 使用道具

舉報

發表於 2014-3-12 09:23:53 | 顯示全部樓層
本帖最後由 auraheart 於 2014-3-12 09:25 編輯
柒喜 發表於 2014-3-12 09:19
黑膠係統迷人地方就係好玩多野玩,乜都可以換,要平要貴任君選擇


迷人地方就係good sound, once you are into it...貴!  Just the motor costed me about 1,000 USD.  Back then you can get a new cheap car for about 4,000 USD.  Maybe a low end Chevy or Toyota, or Volks Wagon bug.
回覆 讚好 不讚 使用道具

舉報

發表於 2014-3-15 14:59:46 | 顯示全部樓層
本帖最後由 auraheart 於 2014-3-16 06:38 編輯


1970's was the era of low mass and high compliance tonearms. (super tracking) Two arms on top pic were higher mass, low compliance which should not have been used..SME 3009S2, second looks like SAEC arm from Japan.  Third is lower mass , rear part look like ADC and rest looks like infinity.  In the 80s, more and more good moving coil (sweet sounding) available which are higher mass and lower compliance...I had to change to a wooden arm which is high mass/low compliance.  It is very hard to have a good turn table system, a lot to learn.  Installing a good uni pivot arm is a pain especially if drilling hole and measurements needed, like the Denon DP 6000/DP 80 with such an arm. (pic shown above does not require drilling hole and they are not uni pivot, easy to install)
回覆 讚好 不讚 使用道具

舉報

您需要登錄後才可以回帖 登錄 | 註冊

本版積分規則

Archiver|聯絡我們|141華人社區

GMT+8, 2024-11-9 06:04

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

快速回覆 返回頂部 返回列表